Best DIY Ring Light Photography, Video, Selfie

November 10, 2016

5 Reasons You MUST Try Out a Ring Light This Weekend
If you’ve never given a ring light a try, this weekend is the time to make. it. happen. Beyond offering beautiful, soft light that is perfect for capturing amazing straight on portraits, there are many reasons why you should add the ring light to your repertoire.

1. That Catch Light Tho
The first is the most obvious: a ring light means one of the coolest, most attractive catch lights (the light reflection in your subject's eye) in the business!
2. It Makes a Awesome Prop
The light doesn’t have to be off-camera. In fact, one of the coolest effects you can get in a portrait is to have your subject hold it themselves. The darker the surroundings the better: let that ring be the only source of light.
3. You Can DIY Your Own for Cheap
His cost only $70, but he estimates that it’ll run you between 50 and 100 depending on how fancy you want to get. The results he’s gotten (like the photo below) speak for themselves. “I can’t afford it” isn’t a good excuse… sorry.
4. It Helps You Capture Killer Closeups
The very nature of a ring light requires that you get very close, and the way the light spills across your subject’s face is absolutely stunning. When taking close-ups, a ring light is extremely hard to beat…
5. It’s Great for Macro Photography
The ring light reflection in the drops is gorgeous, and the close-up nature of a ring light/ring flash makes it perfect for many macro photography applications.
If water drops aren’t your thing, here’s another beautiful macro example captured with a ring light:

Basic ring lights range in price from cheap $10 bulbs to $100 and beyond for higher-end LED setups.

More information: 500px

DIY: How To Build Your Own Ring Light
Meet Jay Russell a.k.a. The Photo Fiend, a self-taught creative portrait photographer based in Calgary. Want to improve your portraits with a full, soft light on your model? Jay can teach you how to make your own ring light. So you too can use it to shoot stunning portraits like the images below!

HOW TO MAKE YOUR OWN RING LIGHT
by Jay Russell

This is a tutorial on the ring light I made that I use for most of my portrait work on 500px. I’ve made a few DIY lights since making my first ring light, but I still prefer the original 12 lights on a 24″x 24″ plywood to be the best light for my portraits.

It’s not difficult to build, but just a warning—because you are working with electricity, I recommend getting an electrician to build it for you or at least provide you with some guidance. If you wire something wrong, you can easily end up electrocuting yourself, so please be safe and take all the necessary precautions.

You can do this project for about $50-$100, depending on the specific materials you decide on using. My cost for this project is $70.
It will take about 1-3 hours to complete.

MATERIALS

14-gauge household wiring (approximately 10 ft)
Standard light sockets x 12
24″x 24″ plywood. I used 1/4″ fir, 3/8 would be stronger
A light switch. I decided on a 600-watt dimmer switch
12 light bulbs. CFL or incandescent work fine. Keep in mind incandescents run hot.

Make sure you don’t go over the wattage that your switch can handle. I used regular 40-watt household bulbs.

Power cord
Small bag of wire connectors
Zip ties
Bracket and spigot for mounting to a light stand
Electrical tape
Electrical box

TOOLS

Jigsaw
Drill
Wire cutters and strippers
Screwdriver
Pliers
Box cutter
Measuring tape
Pencil
String

INSTRUCTIONS

Measure and mark the center of your plywood at 12 inches. Then attach the string to your pencil to draw the inner circle you need to cut out. Use one of the light sockets to gauge the distance you need to make it. Then, do the same for the outer circle.

Use the jigsaw and cut out your inner and outer circles. For the outer circle, leave one corner in tact, so you have a spot for the switch and mounting bracket. Once you are done, you’ll have a teardrop shape with a hole in it. You can measure and mark 12 evenly spaced points for the light sockets. I just spaced my sockets out and marked everything without measuring. Drill the 12 holes out with a 7/16″ bit, or whatever is close enough so that you can feed 4 wires through.

Next you’ll need to strip the wire. Remove the outer shield and cut off 8-10″ strips of the black and white pairs. You’ll need 12 pairs in total. Then you’ll need to strip the ends of every wire, roughly 3/4″ bare wire and use the pliers to make hooks on the bare wire. You’ll feed 4 wires through each of the 12 holes you drilled and wire each light socket.

I wired mine in parallel. You’ll want to take your time, and make sure you don’t mix up the polarity. The 2 white wires go to the two gold contacts on the light socket. The 2 black wires go to the silver contacts. Make sure you feed the wire onto the contacts clockwise, so that when you tighten the screws, the wire doesn’t spin off. Double check your work, and do not mess this up. As you wire around the ring, you should have 1 white and 1 black wire left. Do not wire these into the socket you started with—you will wire these into the switch according to the instructions that come with your switch.

For my dimmer switch:
White wire goes directly to the power cord
The black gets wired into the switch
The ground from the switch goes to the ground on the green power cord

Secure your wires with wire connectors and tape them.

Now is a good time to test your handiwork. Screw a light bulb into the last light socket, and test it out. It should work like a regular light switch. If it doesn’t work, then you messed up and you’ll need to unplug your light and double check your wiring.

After you know your wiring works and it’s NOT plugged into the outlet, zip tie everything in place. Drill small holes for the zip ties. You can also cut off the tip of the teardrop, so you have a flat edge for your mounting bracket. Important: Make sure you are NOT plugged into the wall when you’re working on your light! I zip tie everything, including the bracket and switch. Make sure there is no bare wire coming out the back of the light sockets or the switch.

Throw your ring light on a light stand, screw in your bulbs and test it out!

We hope you found this tutorial helpful! Follow Jay Russell on instagram to see more of his work.

November 10, 2016

How to Build a Cool DIY Ring-Light for Just $25
On this video Matthew Perks from the popular Youtube DIY channel DIY Perks, demonstrates an interesting photography/videography related lighting DIY project for building an inexpensive ring light from LEDs.

Perks didn’t use heat-sinks for the LEDs – this can be a problem as LEDs get very hot very quickly so it is very much recommended that you do connect heat-sinks to remove access heat.
As always – these sorts of DIY projects can be dangerous (LEDs can easily melt and batteries might explode if they get too how) so do this at your own risk and only if you know what you are doing!

November 10, 2016

DIY Ringflash

THE MATERIALS:

12 5-10W led light bulbs dimmable
12 E27 Sockets
Light dimmers
Some wires made for lamps (2×1,5mm2) flat cable
2 70x40mm angles
Some screws and bolts.

Using screws, or cable ties, attach the 12 sockets to the chandelier at even spaces. Adding A Mounting Bracket. Place the two angles opposite of each other. Place the Chandelier in the middle with both rails caught by the angles. Lock the angles with a bolt and a nut.

More information: diyphotography

November 10, 2016

Ringlights create interesting reflections in the eyes
Diamond created the ring light using what seems to be a panel board, which he carved to create holes to fit light bulb holders. He also carved out some notches to allow him to shoot through at different angles as well as make the whole thing lighter. The main benefits of using a ringlight is being able to shoot with a shallow depth of field.